Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
Listed here in the next paragraph you can locate a lot of sensible points in relation to How to Install a Bathtub.
Installing a tub isn't exactly rocket science, however it does require solid plumbing, woodworking, and also often, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately difficult job. If the old bathtub is conveniently obtainable, the job can move speedily; if you need to open up a wall to remove the old tub and place the new tub, the job is much harder. In either situation, the task is within a house handyman's skills, although you will need a helper to leave the old tub as well as embeded in the brand-new one. See to it you have actually certified yourself for the job as well as are comfortable attempting it. Instead of employing a specialist to take over a halfway-completed project, it is far better to consider utilizing one prior to you start. Possibilities are you might need an expert plumber to make tube links.
This article will aid you mount a new bathtub in your bathroom if you have actually currently gotten a new tub and also don't need to change the plan of your previous water pipes.
Your tools and material checklist should consist of the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you must do is disconnect the supply of water. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly problematic as a result of the limited access that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the taps. Have a towel all set for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washers remain in area in between the faucet and the sink. Protect the faucet in place with the manufacturer offered backnut. When the faucet is firmly in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet adapters. The previous kind ought to be connected to the tap finishes initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bathtub
Making use of both wood boards under its feet, position the bathtub in the called for placement. The wood boards are handy in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by examining the spirit level and also readjusting the feet on the bathtub up until the level checks out degree.
To install taps, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression join; after that do the very same for the various other tap.
Turn on the water supply and also inspect all joints as well as new pipework for leakages and tighten them if essential. Load the bath tub and additionally check the overflow electrical outlet as well as the regular outlet for leakages.
Lastly, deal with the bath paneling as explained in the manufacturer's user's manual. Tiling and sealing around the bath tub must wait till the bath tub has been utilized at least once as this will resolve it right into its last position.
Preparing for the Installation
Firstly, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets system to avoid pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of the two faucets making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall surface in between the bath as well as the tiling, causing complications with wetness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures and fittings. They are offered in tubes as well as cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealer can break fairly very early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly offered on the market. It is recommended to fit the floor tiles using waterproof or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave feedback below. We would be delighted to see your thoughts about this blog post. We are looking forward that you come back again soon. If you please take the opportunity to share this post if you enjoyed reading it. Thanks for going through it.
Dial, rest easy! Report this page